Wednesday, 30 May 2012

Brands Hatch Indy - May 29th 2012

It's May 29th, the sun is out, the Clio is full of tools, man food and V-power so we're ready to take on the famous Brands Hatch Indy circuit!
Upon arrival we managed to reserve a paddock prior to the briefing which was pretty boring but essential no less. With the formalities over with we then unloaded the car including spare wheel, jack and rear bench. Baz then set off with the Clio for noise testing which passed - this is always a good start to the day! We managed to set up base next the a guy named Chris who owned 1 of 3 nice looking Clio's at Brands Hatch that day. It has to be said that Red ones go faster, of course :)


And then finally it was time for Dad with Paul as co-pilot to hit the tarmac! On go the crash hats and around they go for 3 sighting laps behind the pace car. It's only at this stage as a driver that you realise the real contours of the track, especially the incline that is the dreaded Paddock Hill Bend. Their faces said it all as they headed back to the pit lane - a composure of absolute fear and child-like excitement for what was yet to come :)


Next up was Baz as driver with my self on the pace notes for the first track session. Without a moments hesitation, Baz was on the gas, into Paddock Hill with live commentary from the drivers seat and i quote:

"BMW M3? Three hundred plus horse power? GET OUT THE WAY CLIO COMING THROUGH, YES BOY!"

He done well over taking most of the novices on track, but was promptly shown the 'TYRES' board by the track official for excess squealing. A little less enthusiasm and a little more technique into those corners next time eh, Baz? hehe! Tyre's took a bit of a pounding on the outer edges, but a good effort all the same :)


Dad was up next for his first session on track, again with Paul holding on to the Jesus bar! He looked confidant into most corners and managed to over take a Lotus Ellise! He hasn't quite found his comfort zone through Clearways and out of Clarke Curve just yet. Not the easiest bend on the track I'll admit and with several racing lines to pick out, you don't want to get it wrong with a gravel trap waiting to swallow you up either.


My self and Paul had more of a placid approach as we were both under tuition by the MSV instructors. What an experience that was!! We both came back into the pits trembling with nerves and with our brains fried as there was so much information to take in. We were forced to put all of our faith into the instructor and ignore our basic survival instincts.

With every part of my body instinctively telling me to brake at over 100mph, there was a voice repeatedly telling me to "STAY ON THAT GAS.....NOW BRAKE, BRAKE HARD!"

Joking aside, we definitely picked up a few tips which are going to help us improve our lap times on the next trip to Brands Hatch, so as terrifying as it was, thank you Chiok for booking the driver tuition as part of my wedding gift - much appreciated :)


 

Thursday, 3 May 2012

First Track Day Booked!

So, what have we been up to? Well, finally we've booked our first track day for May 29th at Brands Hatch (Indy circuit)!

We also had the car weighed on the local weigh bridge and found that with a 1/4 tank of fuel it comes in at 1,100kg, which is pretty much as we'd expected for a standard set up. We aim to get this down to around 900kg later on when the MOT expires and the car is taken off the road. All in good time.


We say a big THANK YOU to our first sponsors; Jeff & Mike @ Import RP for donating us credit, which we've used towards purchasing this digital gauge kit which includes oil temp, oil pressure, voltage meter and carbon DIN panel.

We look forward to proudly displaying the IRP logo on the track car and to fitting the gauges when they arrive - thanks again :)

 Many thanks to Simon @ Black Diamond Performance who is kindly donating a set of stainless brake lines for the front & rear of the Clio. We have a space reserved on the car for your logo's as well - thank you for your support!

Roll on May 29th :)


Friday, 20 April 2012

The timing belt change was relatively pain free. The only additional expense to the job was the drivers side top engine mount which had certainly seen better days.



An over night delivery was sorted at 2pm, the replacement arrived at 9am the next morning and the whole job, engine mount and all was finished for lunch time - not bad going!





Big thanks to:

Kris & Bob @ Mongers Garage, Maidstone, (01622) 751258
The Renault Centre, (01394) 775799
Chiok @ UniPart, Maidstone, (01622) 716191


With the car now pulling hard all the way to the red line in every gear, it's time to book a track day!! Woop woop :)

Tuesday, 17 April 2012

Dephaser pulley arrives at last!


The new dephaser pulley arrived today, so we're now ready for the timing belt & water pump kit service at the garage tomorrow. All being well with this fitted and working, we'll have a healthy engine, fit and ready for Brands Hatch :)

Sunday, 15 April 2012

Almost ready for the track...

(Friday)  It's been a busy two days spent sorting out lot's of minor but essential pre-track day jobs

Puncture Repair
Luckily the nail didn't puncture the tyre. It was on the outer edge so it wouldn't have been repairable had it gone all the way in - result!




ECU Diagnostic
Bob (Mechanic) noticed the service & air bag lights illuminated on the dash. He was keen to try out his new ECU scan tool and it wasn't going to cost us anything, so he plugged it in and scanned away. All clear except for the side air bag circuit which will soon be removed anyway.

Suspension/Tracking/Tyres
Kris (Mechanic) lifted the car on the ramps so we could investigate possible causes for the car pulling to the right under acceleration. Track rod ends, ball joints and bushes all seem solid enough, but the tyre pressures were slightly out and this seems to have resolved the problem.

Exhaust Mount
As i drove up the steep slope into the garage car park i managed to pull one of the exhaust mounts off! We replaced this and cable tied it on for extra support.

(Saturday) The sun is out, so over to my Dad's house today for more tinkering to the Clio.

Faulty bonnet catch
One minute it's popping up at 40mph, then it doesn't open at all! After some time and moderately foul use of the English language, we managed to get the bonnet open.We completely removed the primary catch mechanism, cleaned it up with some WD40 and adjusted the bolt hole position. Job done!

Front Bumper Alignment
As mentioned in an earlier post the bolts had pulled through the plastic, meaning it was held on by plastic clips alone and occasionally the bumper would pop out from under the arches. Not ideal, so we used the existing bolt holes, new nuts, bolts and over sized washers to keep it secure and tidy.

We got the intended jobs finished with time to spare, so we spent some time tidying up the engine bay, replacing missing nuts, bolts and cable tidies as we went. The car is now safe to drive! The only job left to do before we hit the track is to replace the timing belt, water pump and dephaser pulley :)


(Above) Dad taking pride in his work by buffing up the intake manifold using a power drill attachment :)

Thursday, 12 April 2012

Poxy weather!!


Finally a break in the weather, albeit for half an hour this morning before it lashed down with rain again, but i managed to get a few bits done.

(Left) Front bumper fitted minus the splitter

Now the splitter has been removed we have some ground clearance. We can jump on the anchors without fear of leaving a trail of broken plastic bumper pieces behind us!

As one problem is resolved another if found...... look what i found after jacking the car up - a rusty screw trying to catch a free ride in the drivers side tyre. Hopefully it can be repaired for £20 at the local tyre fitters. It's a brand new as well...


I also removed part of the front, inner wheel arch liners. Why? They were getting in my way for starters! Also because they restrict air flow to the front brakes.

At some stage we'll look into removing those front fog lights so we can replace them with a D.I.Y air duct to the brakes. No doubt it's been done before, so a little research is required in the mean time.